This is a BRAND NEW product by Vito's Performance! Brought back after a few years of hibernation, these are in stock, and ready to ship immediately! These are Vito's BULLSEYE billet aluminum reeds cages & CARBON FLEX black reeds Makes approx 1.2 horsepower over the stock ones, simply by bolting o

This is a complete set of NEW carbon flex intake reeds by Vito's Performance They offer crisper throttle response, and a general overall increase in usable horsepower over the stock reeds These are dual stage, so you can gain top end power without sacrificing lower end grunt These flow more gas an

This is a Yamaha Blaster 200 reed spacer kit - these are 5/16" thick These go right up against the cylinders and the carb boots. They are ready to install on ANY year Blaster 1988-2006. Includes all 4 allen head stainless steel bolts and also includes all gaskets required for install (most on ...

This is a Yamaha Blaster Intake manifold reed block valve seat gasket from VITO's PERFORMANCE This goes between the cylinder and intake reed It replaces Yamaha OEM part # 3JM-13621-00-00 Fits any year 1988 to 2006 Blaster YFS200 Will also fits the models below: 1988 YFS200U AIR FILTER 1989 ...

This is a Yamaha Blaster 240 BIG BORE top end gasket from VITO's PERFORMANCE Kit includes: A. .020" base gasket. B. Big bore head gasket fits 71mm to 73mm bore sizes. C. Reed gasket. D. Exhaust gasket. Fits any year 1988 to 2006 1992 BLASTER - YFS200D EXHAUST 1992 BLASTER - YFS200D_MN EXHAUST PIPE ...

Blaster reed ...

This is a BRAND NEW Vito's Performance Oil Injection Billet aluminum block off plate These will fit any year Yamaha Blaster 1988-2006 This removes the UNRELIABLE oil injection system off of your Blaster, so you can pre-mix your own gas. If your factory system fails, your bike will have a ...

This is a set of BRAND NEW Vito's Performance Oil Injection block off kit These will fit any year Yamaha Blaster 1988-2006 This removes the UNRELIABLE oil injection system off of your Blaster, so you can pre-mix your own gas. If your factory system fails, your bike will have a catastrophic (ie ...

This is a BRAND NEW product by Vito's Performance! Brought back after a few years of hibernation, these are in stock, and ready to ship immediately! These are Vito's BULLSEYE billet aluminum reeds cages & CARBON FLEX black reeds Makes approx 2.4HP over the stock ones, simply by bolting on! This

This is a set of 4 BRAND NEW rear Yamaha Banshee or Blaster hydraulic disc brake rotor hub bolts from Vito's Performance Will fit on any year Yamaha Banshee, Blaster, Warrior, or Raptor 660 This includes all 4 bolts needed to install the rotor to the hub They already have Loctite applied to them, ...

This is BRAND NEW OEM factory stock Yamaha blaster intake rubber boot These go right between the cylinder and the carb Its ready to install on ANY year Yamaha Blaster YFS200 1988-2006 Still new in the packaging!

This is an upgraded Yamaha Blaster YFS200 top end gasket from VITO's PERFORMANCE This kit add 1.2 HP over the stock gaskets. Increases your compression by 0 lbs, to achieve these results. Works great with Wiseco pistons, as well as Vito's super Stock pistons. Kit includes: a. HEAD GASKET: .018 ...

The all-new VForce4 is built upon the solid foundation that has made the VForce3 such a success for the last 10 years. While the VForce3 has been continually refined over the years, this is a complete redesign of the entire system. We jokingly say, "The only thing we didn't change is the bolt ...

This is a BRAND NEW aftermarket swingarm bearing carrier rebuild kit for a Yamaha BLASTER 1988-2002 This kit includes the spacer collar, spacer tube, 2 bearings, and 2 dust seals This is ready to install on your BLASTER, and replaces all the internal parts of the carrier assembly ...

This is a Yamaha Blaster YFS200 complete gasket from VITO's PERFORMANCE This is a direct bolt on replacement for the factory Yamaha units Kit includes: A. Base gasket B. Head basket (stock compression) C. Reed gasket D. Exhaust gasket E. Clutch cover gasket F. Oil injection pump gasket Fits any ...

This is a Yamaha Blaster YFS200 top end gasket from VITO's PERFORMANCE This kit add 1.2 HP over the stock gaskets. Increases your compression by 10 lbs, to achieve these results. Works great with Wiseco pistons, as well as Vito's super Stock pistons. Kit includes: A. Base gasket - HIGH ...

This is a Yamaha Blaster YFS200 top end gasket from VITO's PERFORMANCE This is a direct bolt on replacement for the factory Yamaha units Kit includes: A. Base gasket B. Head basket C. Reed gasket D. Exhaust gasket Fits any year 1988 to 2006 1992 BLASTER - YFS200D EXHAUST 1992 BLASTER - YFS200D_MN ...

This is a BRAND NEW VITO'S PERFORMANCE spacer plate kit for a plus 3 mm Yamaha blaster crank. Fits a Yamaha Blaster, any year, 1988-2006 This is brand new, and include 2 gaskets, one for the top, and one for the bottom Designed for people running a +3mm stroker crank

This is a Yamaha Blaster YFS200 complete gasket kit + complete oil seal kit from VITO's PERFORMANCE This is a direct bolt on replacement for the factory Yamaha units Gasket kit includes: A. Base gasket B. Head basket (stock compression) C. Reed gasket D. Exhaust gasket E. Clutch ...

This is a BRAND NEW Yamaha Banshee lower a-arm bushing replacement kit Fits any Yamaha Banshee 1991-2006, Raptor 700, Raptor 660, or YFZ450, Blaster, Warrior, etc (see list below) Includes enough to do ONE (1) lower a-arm - either LEFT or RIGHT: 2 x Bolt tube 4 x Bushings 4 x Dust caps We have ...

This is a BRAND NEW Yamaha Banshee lower a-arm bushing replacement kit Fits any Yamaha Banshee 1991-2006, Raptor 700, Raptor 660, or YFZ450, Blaster, Warrior, etc (see list below) Includes enough to do TWO (2) lower a-arms - both LEFT AND RIGHT: 4 x Bolt tube 8 x Bushings 8 x Dust caps We have ...