This is a full VITO'S PERFORMANCE JETTING KIT! This is everything you need to take your stock carbs from factory setting to accommodate aftermarket pipes Enough jets to do 2 Banshee stock mactory Mikuni carbs, and mods include removal of airbox lid, or pod style filters, and the addition of ...

This is a set of BRAND NEW Vito's Performance T.O.R.S. removal system Works on the stock Mikuni carburetors, are removes the bulky TORS system on top of the carb caps that is very prone to failure. These will fit any year Yamaha Banshee 1987-2006. With these aftermarket carb caps the carbs are ...

This is a brand new VITO's PERFORMANCE billet airbox adapter kit kit includes: Vito's Performance billet adapter plate + mounting hardware Vito's Performance K&N style filter + clamp Outerwear dust bag pre-filter This pro flow adapter eliminates a fatal flaw with the factory design, where dirt and ...

These are in stock, and ready to ship today! This is a brand new set of Vito's Performance FAT BASTARD in-frame pipes The originals are back! After an almost 8 years out of production, the FAT BASTARD pipes are in stock again. This design was custom designed by Vito himself for his racing ...

This is a brand new VITO's PERFORMANCE billet airbox ...

This is a BRAND NEW Vito's Performance Yamaha Banshee carb rebuilt kit This includes everything to completely rebuild your Banshee 26mm Mikuni stock OEM carb Includes the exact items seen in the photos: bowl gasket, main jet, needle jet, seat, needle, orings, clips, springs, etc This will do TWO ...

This is a BRAND NEW clutch side cover gasket from Vito's Performance Goes under the clutch cover on the side of the engine Fits any year Yamaha Banshee 1987-2006 and up All direct OEM replacements, at a fraction of the ...

This is a Vito's Performance SEAL KIT SK350 this is a complete motor engine oil seal kit This will fit any size crankshaft, and includes all necessary engine motor oil seals for a complete overhaul rebuild. Fits a Yamaha Banshee 350, any year, 1987-2006. Seal kit includes: Left crank seal Right ...

This is a stainless steel bolt kit for a Yamaha Banshee Includes a full set of bolts to swap the factory bolts for beautiful Allen Head ones Fits on the Stator cover and the Clutch cover as well Includes Allen Head wrench hardware for installation as well Fits any year ...

This is a PAIR of rear axle nuts for any year Yamaha Banshee 350 or Blaster 200 Brand new from VITO'S PERFORMANCE This is the part that holds the axle, carrier, rear brake rotor, and rear sprocket hub together OEM quality, fit, size, and finish, at a fraction of the dealer price You get 2 units, ...

This is a BRAND NEW aftermarket swingarm bearing carrier for a Yamaha Banshee. Fits 1987-2006 Banshees, and is BRAND NEW, powdercoated silver. These are over $195 new from Yamaha! FREE SHIPPING Upgraded over stock, includes ZERK grease fitting, so keep everything fresh; OEM ones do not have ...

This Listing is a pair of front and rear brake pads for a 1990-2006 Yamaha Banshee. They will also fit 1990-2004 Yamaha Warrior or 2001-2005 660 Raptor. These are BRAND NEW High Quality, excellent stopping power, guaranteed, or your money back. This Listing is for THREE PAIRS of brake pads, ...

This is a NEW complete Yamaha Banshee fuel petcock for the gas tank. This item is brand new, directly from YAMAHA, and an original OEM factory piece. It has never been used, and will fit any year 1987-2006 Banshee. It's the selector switch that you can set to ON, OFF, or RESERVE. This includes ...

This is a pair of 2 BRAND NEW Yamaha Banshee tie rods + ball joints from Vito's Performance These are stock length tie rods (10 3/4") , and are BLACK in color This replaces Yamaha OEM part # 2GU-23831-01-00 and 1UY-23845-01-00 and 1UY-23841-01-00 In stock and ready to ship - you get exactly what ...

This is a BRAND NEW set of 4 Yamaha Banshee headlight stays from Vito's Performance This kit is enough to do TWO HEADLIGHTS These are the stays that mount into the factory headlights to prevent them from tilting up or down Headlight stays will fit any year Yamaha Banshee 87-06, Warrior 93-04, or ...

This kit includes the clutch cover gasket as well! By VITO's Performance This is an aftermarket HIGH PERFORMANCE clutch fiber friction plate and steel/ spring kit for your Banshee Perfect for modified bikes (or stock bikes) - the springs are 15% stronger than stock, so they can handle more ...

This is a set of TWO (2) high temperature exhaust sleeve pipe clamps for a Yamaha Banshee (any year 1987-2006) These are rated up to 500 degrees, and will not melt! These are made with a Silicone Elastomer, with a woven polyester fabric vulcanized and cured In English, that means they are strong, ...

This is a set of BRAND NEW Vito's Performance clutch cable High quality, Heavy duty outer casing OEM factory stock length This is a bolt on direct OEM replacement part, at a fraction of the price These will fit any year Yamaha Banshee 1987-2006. These will fit any Banshee stock or aftermarket ...

This is a brand new o-ring from Vito's Performance This oring replaces the stock one that goes on the aluminum transfer tube on the cases, between the hose and the clutch cover. Replaces Yamaha OEM stock # 93210-17239-00 Will fit any year Yamaha Banshee 1987-2006. Also fits: 2002 F200TXRA ...

This is for TWO (2) brand new K&N style air filters These are 6" long, and fit any aftermarket carburetors 33mm 34mm 35mm or 36mm - including Keihin or Mikuni PJ and PWK carbs WILL NOT FIT STOCK CARBS! We have ones that will in our other listings! The inside diameter of the opening of the filter ...

This is a BRAND NEW set of replacement studs for a Yamaha Banshee head This includes all 10 studs needed, 8 of the standard ones, and 2 of the longer front ones Factory replacement, stock size, ready to install! Will fit any year Yamaha Banshee 1987-2006. ...

This isTWO (2) brand new K&N style air filters + BLACK OUTERWEARS These are 6" long, and fit any aftermarket carburetors 33mm 34mm 35mm or 36mm - including Keihin or Mikuni PJ and PWK carbs These will NOT fit stock carbs, but we do have ones that will fit stock carbs for sale in our other ...

This is .020, stock size, factory replacement Fits any year Yamaha Banshee 1987-2006 and up All direct oem replacements, at a fraction of the costs: Yamaha 3GG-11351-00-00 and 3GG-11351-01-00 87 YAMAHA YZF350 T BANSHEE 88 YAMAHA YZF350 U BANSHEE 89 YAMAHA YZF350 W BANSHEE 90 YAMAHA ...

This is TWO (2) brand new K&N style air filters These are 6" long, and fit any aftermarket carburetors sized 38mm 39mm 40mm 41mm - including Keihin or Mikuni PJ and PWK carbs WILL NOT FIT STOCK CARBS! We have ones that will in our other listings! The inside diameter of the opening of the filter ...

This is a brand new 9 piece Yamaha Banshee swingarm bearing kit by Vitos Performance Comes complete with pivot tube, 2 x needle bearings, 2 x dust seals, 2 washers, and 2 x dust caps The rear pivot tube is what the swingarm bolt slides into; it is very common for these to seize up with the bolt ...

This is a BRAND NEW billet aluminum twin row bearing carrier. This is the roundhouse style carrier for aftermarket swingarms. It is the 35mm size, and it will work for stock or aftermarket axles (but not 40mm drag axles). This is ready to install, includes all the bearings and seals needed, and ...

This is a brand new Yamaha Banshee thumb throttle lever assembly by VITO'S PERFORMANCE Ready to install on any year Yamaha Banshee 1987-2006, and it will also fit a Blaster 200 or Warrior 350. This is for one with the wire attached, but please check your plug style first replaces OEM Yamaha part ...

This is a set of Vito's Performance standard size MAIN HEX JETS for a KEIHIN PWK or PJ carburetor 10 sizes included: 150 152 155 158 160 162 165 168 170 172 We use them for Yamaha Banshee and Blaster carbs mostly, but will work with any Keihin style carb - PWK PJ included Great complete set! ...

This is a PAIR (2) brand new headlight bulbs by Vito's Performance These will fit any year Banshee, Warrior, Raptor 660 700, or YFZ450, as well as many others (listed below) These are 35W each, and produce a super bright WHITE light (not blue!) - nice upgrade over stock These are dual ...

*** This includes the 2 handlebar clamps and the 4 mounting bolt unlike the competition *** This is a BRAND NEW Yamaha Banshee steering stem by Vito's Performance Factory stock size (+0") Painted BLACK Will fit any year Banshee 1987-2006 These fit the same 7/8" handlebars as the stock Banshee ...

This is a brand new Yamaha Banshee swingarm bearing kit + swingarm bolt by Vito's Performance complete with Pivot tube, 2 x needle bearings, 2 x dust seals, and 2 x dust caps, swingarm main bolt, washer, and nut The rear pivot tube is what the swingarm bolt slides into; it is very common for these ...

This is a BRAND NEW Billet aluminum polished intake ...

This is for a set of 4 BRAND NEW rubber grommets by Vito's Performance This replaces Yamaha OEM # 90480-18411-00 These are the rubber plugs that go in the metal heel guards by the footpegs, and they hold in the plastics This is for a set of 4 (four) - enough for both left and right sides Also used ...

This is a set of 4 pipe springs for many different ATVs and dirtbikes These are STAINLESS STEEL - and will be rust free for a lifetime of use! These have a swivel on one end, so they can flex, and turn. Makes it much easier to install! These are 83mm, and will fit: Banshee Blaster TRX250R LT250 ...

This is a BRAND NEW aluminum brake stay (rear caliper mounting plate) This includes the aluminum caliper spacers and brake plate retainer spring snap ring. Will fit on 35mm or 40mm carriers 69.9MM ID This has been polished as well, not dull or rough looking like many others on the market. This ...

This is a for 2 x BRAND NEW Yamaha cylinder water jacket rubber plugs These plug up the castings holes for the engine motor where the radiator fluid runs to keep the cylinders cool. These will fit any year Yamaha Banshee or Blaster YFS200 1987-2006 Also fits 1987-1989 Yamaha 570 Exciter and fits ...

This is a BRAND NEW Yamaha Banshee swingarm pivot bolt, nut, and washer by Vito's Performance This is the steel bolt that goes through the frame and holds the swingarm onto the frame Ready to install in any year Yamaha Banshee 350 1987-2006. Replaces OEM Yamaha part #: 2GU-22141-00-00 , ...

This is a BRAND NEW aftermarket VITOS RACING performance plus +4 advance degree timing flywheel key Also known as a woodruff key or timing key This goes on the crankshaft, and hold the flywheel in place at the correct position It will work on any year Yamaha Banshee 1987 - ...

This is a BRAND NEW front 16 tooth sprocket by Vito's Performance fits: 1987-2006 Yamaha Banshee 350 1988-2004 Warrior 350 2004-2013 Raptor ...

This is a BRAND NEW water pump impeller cover gasket from Vito's Performance Fits any year Yamaha Banshee 1987-2006 and up Will also fit a 1984 and 1985 RZ350 All direct OEM replacements, at a fraction of the cost! Replaces: Yamaha 3GG-12428-00-00 and ...

This is a BRAND NEW complete Yamaha Banshee aftermarket HIGH CAPACITY aluminum radiator. This will fit any year 1987-2006, and will keep your Banshee cooler than a factory unit. This holds more liquid than a factory unit, and still retains the original mounting locations. This is a fully ...

This is for TWO (2) brand new K&N style air filters + BLACK OUTERWEARS pre-filters These are 6" long, and fit stock 26mm carbs or other aftermarket - including Keihin or Mikuni PJ and PWK carbs the inside diameter of the mounting opening is approx 1.75" These have a 10 degree angle so they clear ...

This is a set of BRAND NEW Toomey Racing T-5 pipes Brand new, chrome finish, ready to install, complete with rear silencer hangers, and o-rings. You get both header head pipes and both aluminum silencers with stinger tubes. Will fit any year Yamaha Banshee 1987-2006. Ready to install. Similar ...

This is a BRAND NEW factory OEM clutch actuator arm holder clamp. This is a OEM Yamaha unit, brand new from local dealership. This mounts on top of the cases, and its what holds the actuator arm down Ready to install on any year Yamaha Banshee 1987 - 2006. Also fits 1984 1986 RZ350 bike Yamaha ...

This is a BRAND NEW Banshee chrome rear grab bar. EXACT same as the rear bumper guard that came on a 1987 Yamaha Banshee 350 Beautiful perfect condition, ready to install this rear bumper on any year Banshee. This rear grab bar will fit on any year Banshee: 1987-2006. Replaces the following ...

This is a brand new Yamaha Banshee intake airbox + lid + Vitos air filter setup It will fit any year Yamaha Banshee 1987-2006 This is factory OEM unit - directly from Yamaha Includes everything you need to complete an entire airbox! All 28 parts from Yamaha Includes, airbox, lid, snorkel, boots, ...

This is a BRAND NEW product by Vito's Performance! Brought back after a few years of hibernation, these are in stock, and ready to ship immediately! These are Vito's BULLSEYE billet aluminum reeds cages & CARBON FLEX black reeds Makes approx 2.4HP over the stock ones, simply by bolting on! This ...